8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Switch User Manual DN-650102
7 Pin MDI-X Signal Name MDI Signal Name 1 Receive Data plus (RD+) Transmit Data plus (TD+) 2 Receive Data minus (RD-) Transmit Data minus (TD-)
8 Cabling Use four twisted-pair, Category 5e or above cabling for RJ-45 port connection. The cable between the switch and the link partner (switc
9 Figure 2.9: Transceiver Inserted Second, insert the fiber cable of LC connector into the transceiver. Figure 2.10: LC connector to the transcei
10 To remove the LC connector from the transceiver, please follow the steps shown below: First, press the upper side of the LC connector to release
11 Wiring the Power Inputs Please follow the steps below to insert the power wire. Insert the positive and negative wires into the V+ and V- conta
12 Note The wire gauge for the terminal block should be in the range between 12~ 24 AWG.
13 Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is not screwed on
14 1. First, insert the top of DIN-Rail into the track. 2. Then, lightly push the DIN-Rail into the track. 3. Check if the DIN-Rail is tight
15 Wall Mount Plate Mounting Follow the steps below to mount the industrial switch with wall mount plate. 1. Remove the DIN-Rail from the industria
16 Hardware Installation In this paragraph, we are going to mention how to install the 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE In
FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules.
17 Network Application This segment provides the samples to help user have more actual idea of industrial switch application. For a sample applicat
19 Troubles shooting Verify that is using the right power cord/adapter (DC 48V), please don’t use the power adapter with DC output voltage highe
20 Technical Specification 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Switch technical specifications is shown
21 Optical cable Distance: Multi mode: 0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km) 0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km) Single mode: 0 to 40 k
22 Operating Humidity 5% to 95% (Non-condensing) Storage Temperature -40oC to 85oC Case Dimension IP-30, 72 mm (W) x 105 mm (D) x 152mm (H) EMI FCC C
Content Introduction ... 1 Features ...
1 Introduction The 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Switch is a cost-effective solution and meets the
2 Package Contents Please refer to the package contents list below to verify them against the checklist. 8 10/100TX + 2 10/100/1000T/100/1000 SFP
3 Hardware Description In this paragraph, the Industrial switch’s hardware spec, port, cabling information, and wiring installation will be describ
4 Top View The top view of the 8 10/100TX + 2 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Switch has one terminal block connecto
5 LED Indicators The diagnostic LEDs located on the front panel of the industrial switch provide real-time information of system and optional statu
6 OFF Not connected to network P1 ~ P8 (Yellow) Yellow Ethernet port full duplex Blinking Collision of packet occurs OFF Ethernet port half duplex
Comments to this Manuals